切换到宽版

[讨论] 请教关于深海项目的防腐标准

微信扫一扫到手机

随时看帖、分享到朋友圈

小编教你如何扫二维码>>
阅读:14326 |   回复:6
 
发帖
150
精华
1 篇
绿叶
164
小红花
25
[复制链接] 只看楼主 倒序阅读 楼主  发表于: 2011-07-01
请教各位侠客:

             哪位对深海钢结构的防腐标准比较清楚?有哪些?
            个人认为应该与常规项目执行标准一样吧?有哪些特殊的?

发帖
1066
精华
0
绿叶
767
小红花
1544
只看该作者 沙发  发表于: 2011-07-01
引用楼主菲我莫属于2011-07-01 15:18发表的 请教关于深海项目的防腐标准 :
请教各位侠客:
             哪位对深海钢结构的防腐标准比较清楚?有哪些?
            个人认为应该与常规项目执行标准一样吧?有哪些特殊的?

        
         深海钢结构啊,你想知道什么样的,海底撬块,设备还是海底储罐、浮筒类的结构的防腐要求呢?  
发帖
150
精华
1 篇
绿叶
164
小红花
25
只看该作者 板凳  发表于: 2011-07-03
引用第1楼syyin于2011-07-01 15:44发表的  :
        
         深海钢结构啊,你想知道什么样的,海底撬块,设备还是海底储罐、浮筒类的结构的防腐要求呢?  



海底撬块的,水下管汇,海底储罐的都行啊。我觉得标准应该还差不多。你有相关资料么?分享一下,十分感谢啊!

发帖
1066
精华
0
绿叶
767
小红花
1544
只看该作者 地板  发表于: 2011-07-04
引用第2楼菲我莫属于2011-07-03 10:16发表的  :
海底撬块的,水下管汇,海底储罐的都行啊。我觉得标准应该还差不多。你有相关资料么?分享一下,十分感谢啊!


            打砂喷漆的基本要求都是一样的,就是深海钢结构,对打砂的表面处理和盐分含量要求较高,一般喷砂到Sa3,盐分要低于20mg/m2。使用能兼容阴极保护的油漆系统,在常规检验项的基础上,需要增加漏涂点的检测。


[ 此帖被syyin在2011-07-19 14:12重新编辑 ]

发帖
1066
精华
0
绿叶
767
小红花
1544
只看该作者 4楼 发表于: 2011-07-04
不过海底管道的涂装要单独考虑,海底金属管道一般采用涂敷层和阴极保护结合的方式来保护,而聚乙烯防腐技术是目前国内外海底管道外防腐的主要技术体系之一。
发帖
29
精华
1 篇
绿叶
109
小红花
572
只看该作者 5楼 发表于: 2011-07-07
关于深海和浅海的区别,个人认为主要是在“力学”方面,也就是主要反映在各个结构的强度上面,对于防腐方面的要求与浅海区别不大,以下是一些海底防腐常用的相关标准,希望对大家有用:
ASTM C518 Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus
ASTM D36 Test Method for Softening Point of Bitumen (Ring-and-Ball Apparatus)
ASTM D149 Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electric Insulating Materials at Commercial Power Frequencies
ASTM D256 Test Method for determining the Izod Pendulum Impact Resistance of Notched Specimens of Plastic
ASTM D257 Test Method for D-C Resistance or Conductance of Insulating Materials
ASTM D570 Test Method for Water Absorption of Plastics
ASTM D638 Test Method for Tensile Properties of Plastics
ASTM D746 Test Method for Brittleness Temperature of Plastics and Elastomers by Impact
ASTM D785 Test Method for Rockwell Hardness of Plastics and Electrical Insulating Materials
ASTM D790 Test Method for Flexural Properties of Unreinforced and Reinforced Plastics and Electrically Insulating Materials
ASTM D792 Test Method for Density (Relative Density) and Specific Gravity of Plastics by Displacement
ASTM D870 Practice for Testing Water Resistance of Coatings Using Water Immersion
ASTM D1000 Test Methods for Pressure-Sensitive Adhesive- Coated Tapes Used for Electronic and Electrical Application s
ASTM D1002 Test Method for Apparent Shear Strength of Single-Lap-Joint Adhesively Bonded Metal Specimens by Tension Loading (Metal-to-Metal)
ASTM D1084 Test Methods for Viscosity of Adhesives
ASTM D1149 Test Method for Rubber Deterioration – Surface Ozone Cracking in a Chamber
ASTM D1238 Test Method for Flow Rates of Thermoplastics by Extrusion Plastometer
ASTM D1525 Test Method for Vicat Softening Temperature of Plastics
ASTM D2084 Standard Test Method for Rubber Property –Vulcanization Using Oscillating Disc Cure Meter
ASTM D2240 Test Method for Rubber Property–DurometerHardness
ASTM D3418 Test Method for Transition Temperatures of Polymers by Thermal Analysis
ASTM D3895 Test Method for Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry
ASTM D4060 Test Method for Abrasion Resistance of Organic Coatings by the Taber Abrader
ASTM D4285 Test Method for Indicating Oil or Water in Compressed Air
ASTM E96 Test Methods for Water Vapour Transmission of Materials
ASTM G8 Test Method for Cathodic Disbonding of Pipeline Coating
ASTM G14 Test Method for Impact Resistance of Pipeline Coatings (Falling Weight Test)
ASTM G17 Test Method for Penetration Resistance of Pipeline Coatings
ASTM G21 Practice for Determining Resistance of Synthetic Polymeric Materials to Fungi
ASTM G22 Practice for Determining Resistance of Plastics to Bacteria
BS 903 Part A1 Physical Testing of Rubber. Determination of Density
BS 3900 Part F4 Resistance to Continuous Salt Spray
BS 4147 Specification for Bitumen-Based Hot-Applied Coating Materials for Protecting Iron and Steel,Including Suitable Primers Where Required
BS 6374 Part 5 Lining of Equipment with Polymeric Materials for the Process Industries Part 5. Specification for Lining with Rubbers
CAN/CSAZ245.20/21    External Fusion Bond Epoxy Coating for Steel Pipe–External Polyethylene Coating for Pipe
DIN 30670 Polyethylene Coatings of Steel Pipes and Fittings; Requirements and Testing
DIN 30672 Coatings of Corrosion Protective Tapes and Heat Shrink Sleeves; Materials for Pipelines for Operational Temperatures up to 50°C
DIN 30678 Polypropylene Coatings for Steel Pipes
DIN 53516 Testing of Rubber and Elastomers; Determination of Abrasion Resistance.
DNV-OS-F101 Submarine Pipeline Systems
DNV-RP-F106 Factory Applied External Pipeline Coatings for Corrosion Control
DNV-RP-F103 Cathodic Protection of Submarine Pipelines by Galvanic Anodes
EN 1426 Methods for Determination of Softening Point of Bitumen (Ring and Ball)
EN 10204 Metallic Products – Types of Inspection Documents
EN 12068 Cathodic Protection – External Organic Coatings for the Corrosion Protection of Buried or Immersed Steel Pipelines Used in Conjunction with Cathodic Protection –Tapes and Shrinkable Materials
共有1人赞这个帖子小红花+2
今晚打老虎 小红花 +2 2011-07-07

发帖
10
精华
0
绿叶
279
小红花
22
只看该作者 6楼 发表于: 2021-04-29
大不一样!